Micro Motion RFT9709 Manual de instrucciones Pagina 35
- Pagina / 214
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using ProLink
®
Software with Micro Motion
®
Transmitters
21
Getting Started
continued
Connecting to the transmitter
File Menu: Print File Menu: Log Files View Menu: VariablesBefore You Begin Getting Started File Menu: Database
Windows
®
hour glass
When the Windows hour-glass symbol does not disappear, the ProLink
program has experienced a fatal error. Reboot the computer, then refer
to
Table 2-3
for typical causes and appropriate corrective actions.
Transmit light on PC Interface adaptor
flashes while trying to connect to
transmitter using the RS-485 physical
layer
Conflict between physical layer settings Ensure that transmitter and ProLink
setup, and position of selector switch on
PC Interface adaptor, are all set to
RS-485
Improper wiring between PC Interface
adaptor and transmitter
• Ensure proper RS-485 wiring (see
“Wiring to the transmitter” on page 7)
• Verify terminal blocks are firmly seated
at transmitter and PC Interface adaptor
Incorrect communication parameters Verify that settings for protocol (HART or
Modbus
®
), baud rate, parity, and stop
bits are the same for the transmitter and
ProLink program
Incorrect polling address Open the File menu, then choose
Connect. Click the Poll Network button in
the Connect dialog box, then choose Poll
for a list of available transmitters
Baud rate too high for computer Change ProLink baud rate to 1200 baud,
then reset to higher rate is desired: Open
the File menu, then choose Comm
Options
RFT9739 not properly configured for
RS-485
Change RFT9739 settings (see the
instruction manual that was shipped with
the transmitter)
RFT9712 or RFT9729 not properly
configured for RS-485
See the RFT9712 or RFT9729
instruction manual to verify:
• The communications jumper located
on the processor board in the
RFT9712 or RFT9729 is set to 485
• The RFT9712 or RFT9729 is using
1200 baud for HART communication,
and has transmitter software version
5.0 or higher
Noise interference Ensure proper RS-485 wiring (see
“Wiring to the transmitter” on page 7)
Table 2-2. Troubleshooting the "cannot find" message
Status Cause Corrective Action
- Using ProLink 1
- Software 1
- Transmitters 1
- Appendixes 10
- Contents 11
- 1 Before You Begin 15
- The ProLink 16
- kit and system requirements 16
- Customer service 17
- 2 Getting Started 19
- Getting Started 20
- 2.2 Communication standards 20
- 2.3 Wiring to the transmitter 21
- 2.4 Connecting to the PC and 26
- 2.5 Installing the software 27
- Program Group dialog box 28
- 2.6 Start-up 32
- 2.7 Connecting to the 32
- Menu bar 33
- Cannot Find message 33
- hour glass 35
- Communication options 36
- Software communication 37
- 2.9 Exit 39
- 3 File Menu: Database 41
- File Menu: Database 42
- 3.2 File selection 42
- Directory list box 42
- Database command buttons 43
- 3.5 Load command 45
- 3.6 Send command 45
- Remove command 46
- 4 File Menu: Print 47
- Print setup 48
- File Menu: Print 49
- Destination 49
- Transmitter connections 49
- Fields on ticket 50
- Figure 4-4. Edit Field Tag 50
- Parameter dialog box 50
- Separator and book ends 51
- 4.3 Print 52
- 4.4 Interval print 53
- 4.5 Update rate 54
- Figure 4-7. Print - View 54
- Application - Update 54
- Rate dialog box 54
- Print file 55
- 5 File Menu: 57
- Error and Change Log Files 57
- Error log options 58
- 5.2 Change logging 58
- Log file name 59
- Change log options 60
- 6 View Menu: Variables 61
- View Menu: Variables 62
- 6.3 Output levels window 63
- 7 View Menu: Status 67
- View Menu: Status 68
- Table 7-1. Status indicators 68
- 7.2 Fault outputs 70
- 7.3 Critical indicators 70
- Critical indicators 71
- Operational indicators 76
- "Slug Flow" 77
- Analog and frequency 78
- 7.5 Informational indicators 80
- Zero indicators 81
- Analog Fixed indicators 83
- "Burst Mode" 83
- Informational indicators 84
- 8.1 Overview 85
- Flow calibration factor 87
- Sensor or transmitter 90
- Field flow-calibration 90
- 8.3 Density factors for 92
- Density characterization 93
- 8.4 Density factor for 94
- IFT9701/IFT9703 and 94
- Slug flow limits 95
- 8.6 Temperature factor for 96
- Configure Menu: Characterize 100
- 8.7 Pressure compensation 100
- Real-time compensation 100
- Compensation for stable 101
- Transmitter Variables 105
- 9 Configure Menu: 105
- Overview 106
- 9.2 Flow units 107
- Flow units 108
- Special flow units 110
- Software with Micro Motion 111
- Transmitters 111
- Special units of mass for 112
- Figure 9-6. RFT9739 for Gas 114
- 9.3 Density units 114
- API gravity 114
- API standard volume 115
- 9.4 Temperature and pressure 116
- 9.5 Flow cutoffs 116
- Flow cutoffs 117
- Problem: 117
- Solution: 117
- 9.6 Flow direction 118
- 9.7 Internal damping 119
- Internal damping 120
- 10 Configure Menu: 121
- Transmitter Outputs 121
- RFT9739 outputs 123
- IFT9701/IFT9703 outputs 123
- RFT9712/RFT9729 outputs 123
- 10.2 Frequency/pulse output 123
- Frequency/pulse output 124
- Maximum pulse width for 125
- K-factor 126
- 10.3 Milliamp outputs 126
- Milliamp output variables 126
- Range limits 127
- Milliamp output flow 127
- RFT9712/RFT9729 127
- Added damping on 128
- 10.4 Fault indicators for 129
- Configuring fault 130
- 10.6 Control output from 131
- 11 Configure Menu: 133
- Transmitter Information 133
- 11.2 Transmitter database 135
- 11.3 Pressure input for 136
- Pressure input for RFT9739 137
- 12 Configure Menu: Events 141
- Configure Menu: Events 142
- 12.4 Reading event states 144
- 13 Configure Menu: 145
- Meter Factors 145
- Configure Menu: Meter Factors 146
- 13.3 Entering meter factors 146
- 14 Calibrate Menu 147
- Calibrate Menu 148
- Diagnosing zeroing failure 150
- Convergence limit 150
- Zero time 151
- 14.4 Density calibration 152
- Density calibration for 153
- Table 14-2. Density of air 155
- Table 14-4. Density of water 157
- IFT9701/IFT9703 158
- 14.5 Temperature calibration 162
- 14.6 Milliamp output trim 165
- Preparing for milliamp 165
- Performing milliamp 166
- 15 Test Menu 169
- Milliamp output testing 170
- Applications Menu Help Menu 171
- Configure Menu: 171
- Calibrate Menu Test Menu 171
- Test Menu 173
- 16 Applications Menu 175
- Applications Menu 176
- 16.3 Application builder 177
- 17 Help Menu 179
- Help Menu 180
- 17.3 Keyboard 180
- 17.4 Using Help 180
- 17.5 Context-sensitive Help 180
- Getting around in Help 181
- Jumping from one Help 182
- 17.7 Glossary of terms 182
- B.1 Uploading files 185
- Uploading files 186
- B.2 Downloading a 188
- Flow and Density 191
- Worksheets 197
- • RFT9379 Calibration Record 203
- Flowmeter Calibration Records 204
- Micro Motion Inc. USA 214
- Worldwide Headquarters 214
- Micro Motion Europe 214
- Micro Motion Asia 214
© 2020, manymanuals.es. Todos los derechos reservados | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales